Experimental investigation on the invert stability of operating railway tunnels with different drainage systems using 3D printing technology

In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently, which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure (EWP). By means of a three-dimensional (3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system (TDS) widely used in China and its optimized drainage system (ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice, including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 kPa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.     

基于人工神经网络的智能化架空线路应变快速解调方法北大核心

为了提高智能化光纤复合架空线路态势感知的实时性,将人工神经网络方法应用于光纤沿线应变解调,确定了神经网络的结构。编程实现了基于洛伦兹模型的最小二乘谱拟合方法和神经网络方法,采用不同信噪比和布里渊频移的布里渊谱训练神经网络,将它们应用于某光纤复合架空线路沿线光纤应变的测量,从不同角度比较了两种方法的计算结果。计算结果表明,神经网络方法能有效获得光纤沿线的布里渊频移进而获得应变,具有与谱拟合方法相似的准确性,但应变解调时间仅约为谱拟合方法的1/20000。研究结果为提高智能光纤复合架空线路态势感知的实时性提供了参考。     

Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

Effect of MoS2/PTFE coatings on performance of Si3N4/TiC ceramics in dry sliding against WC/Co

To enhance the tribological performance of Si₃N₄/TiC ceramics, MoS₂/PTFE composite coatings were deposited on the ceramic substrate through spraying method. The micrographs and basic properties of the MoS₂/PTFE coated samples were investigated. Dry sliding friction experiments against WC/Co ball were performed with the coated ceramics and traditional ones. These results showed that the composite coatings could significantly reduce the friction coefficient of ceramics, and protect the substrate from adhesion wear. The primary tribological mechanisms of the coated ceramics were abrasive wear, coating spalling and delamination, and the tribological property was transited from slight wear to serious wear with the increase of load because of the lower surface hardness and shear strength. The possible mechanisms for the effects of MoS₂/PTFE composite coatings on the friction performance of ceramics were discussed.     

Enhanced luminescence and energy transfer performance of double perovskite structure Gd2MgTiO6:Bi3+, Mn4+ phosphor for indoor plant growth LED lighting

Deep-red light emitting phosphors are widely used in LEDs for indoor plant growth because of the critical role played by red light in plant growth. The luminescence properties of deep-red phosphors are still not well understood at present. An energy transfer strategy is a common and effective method to improve luminescence properties. In principle, the energy transfer process may occur when the sensitizer's emission spectra overlap with the activator's excitation spectra. In this work, Bi³⁺ and Mn⁴⁺ were incorporated into the matrix of Gd₂MgTiO₆ as sensitisers and activators, respectively. Mn⁴⁺ ions tend to occupy the [TiO₆] octahedral site and the Bi³⁺ ions are expected to substituted in the site of Gd³⁺. The energy transfer process from Bi³⁺ to Mn⁴⁺ was realised and the photoluminescence (PL) intensity of Mn⁴⁺ increased with the doping content of Bi³⁺. Upon excitation at 375 nm, the PL intensity of Mn⁴⁺ increased to 116.4% when the doping concentration of Bi³⁺ reached 0.3%. Finally, the pc-LED devices were prepared by a Gd₂MgTiO₆:Bi³⁺, Mn⁴⁺ phosphor. The high red luminescence indicated that this phosphor has potential applications in indoor LED lighting.     

A review study on titanium niobium oxide-based composite anodes for Li-ion batteries: Synthesis,structure, and performance

The growing demands for Li-ion batteries (LIBs) in the electrification revolution, require the development of advanced electrode materials. Recently, intercalating titanium niobium oxide (TNO) anode materials with the general formula of TiNb_xO_2+2.5x have received lots of attention as an alternative to graphite and Li₄Ti₅O₁₂ commercial anodes. The desirability of this family of compounds stems from their high theoretical capacities (377–402 mAh/g), high safety, high working voltage, excellent cycling stability, and significant pseudocapacitive behavior. However, the rate performance of TNO-based anodes is poor owing to their low electronic and ionic conductivities. TNO-based composites generally are prepared with two aims of enhancing the conductivity of TNO and achieving a synergic effect between the TNO and the other component of the composite. Compositing with carbon matrices, such as graphene and carbon nanotubes (CNTs) are the most studied strategy for improving the conductivity of TNO and optimizing its high-rate performance. Also, for obtaining anode materials with high capacity and high long-term stability, the composites of TNO with transition metal dichalcogenides (TMDs) materials were proposed in previous literature. In this work, a comprehensive review of the TNO-based composites as the anodes for LIBs is presented which summarizes in detail the main recent literature from their synthesis procedure, optimum synthesis parameters, and the obtained morphology/structure to their electrochemical performance as the LIBs anode. Finally, the research gaps and the future perspective are proposed.     

堆本体抗震试验动力相似关系推导与验证

为确保堆本体抗震试验中流体对流效应、脉冲效应和堆本体结构响应的准确性，需保证重力、流体与固体惯性力、结构弹性力和结构应变的相似性。本文从固体结构的振动方程、不可压牛顿流体的动力学方程、流固交界面的边界条件和环形柱体域内液体线性晃动的动力学公式出发，基于控制方程的量纲分析法，推导了考虑液体晃动效应的堆本体地震响应动力相似关系。基于上述相似关系建立了堆容器堆内构件和堆容器内自由液面流体域的缩尺模型，通过有限体积法分析堆容器堆内构件原型和缩尺模型中液体的晃动固有频率、晃动波高、压力以及液体晃动对堆容器支承裙的倾覆力矩。结果表明本文动力相似关系具有合理性和准确性，可用于堆本体缩尺模型的抗震试验研究。